Back to Blog
How-to Guides 2026-11-14 Outdoor Apparel, Footwear & Equipment | JACK WOLFSKIN 0 views

How to Fit and Load an ALL-IN PACK 30 Hiking Backpack

How to Fit and Load an ALL-IN PACK 30 Hiking Backpack

Set up the ALL-IN PACK 30 for a day hike: adjust the removable waist belt, use the rolltop and security loop, and pack around the padded e-device compartment.

Start with the ALL-IN PACK 30's adjustable features

The ALL-IN PACK 30 is a rolltop daypack with a removable waist belt and a padded e-device compartment. That combination makes it as suitable for commuting and travel as for light hikes and everyday living. Before you load it, decide whether you will wear the waist belt or remove it. For a day hike, keeping the belt attached gives you a way to stabilize the pack; for commuting or travel, you can take it off if you prefer a simpler carry.

The rolltop access is the main opening, and a security loop protects access to the front zipped pocket. Those two features shape how you pack: the rolltop lets you compress the load from the top, while the front pocket is best kept for items you want secured rather than constantly accessed.

Fit the pack before you fill it

Do these adjustments with the pack lightly loaded, then fine-tune once it is full. The catalog does not specify torso length ranges, strap lengths, or a recommended belt position, so use the checkpoints below as general guidance rather than manufacturer instructions.

  1. Decide on the waist belt: The waist belt is removable. If you plan to carry weight for a few hours, attach it and fasten it around your hips rather than your waist. If you are commuting or running errands, you can remove it to reduce bulk.
  2. Set the shoulder straps: Loosen the shoulder straps, put the pack on, and tighten them until the pack sits close to your back without pulling your shoulders down. The catalog does not list strap padding or width, so judge comfort by feel.
  3. Close the waist belt: Fasten the belt and tighten it so it rests on your hip bones. A properly closed belt should carry most of the load; if the shoulder straps still feel heavy, the belt is likely too loose.
  4. Check the rolltop closure: Roll the top down firmly and fasten it before walking. A tight roll keeps the load compact and helps protect gear from the elements, as the rolltop access is designed to do.

Pack for balance, not just capacity

The ALL-IN PACK 30 does not list a volume in liters in the supplied information, so treat its capacity as a daypack rather than a multi-day pack. Pack heavier items close to your back and centered between your shoulder blades, and keep lighter items toward the outside. The padded e-device compartment is a natural place for a tablet or laptop; place it flat against your back panel so its weight stays stable.

Use the front zipped pocket for small, secured items such as keys, a wallet, or a phone. Because the pocket has a security loop, it is a good spot for valuables you do not need to reach constantly. For a day hike, put water and snacks in the main compartment where they are easy to reach when you open the rolltop, and keep a light layer near the top.

Catalog details that affect fit and loading

  • ALL-IN PACK 30: Rolltop access keeps your gear protected from the elements. A rolltop lets you compress the pack from the top, which helps stabilize a partial load on a day hike.
    ALL-IN PACK 30
    ALL-IN PACK 30
  • ALL-IN PACK 30: A simple but effective security loop protects access to the front zipped pocket. Use the front pocket for valuables you want secured, rather than for items you need to grab constantly.
  • ALL-IN PACK 30: The removable waist belt and padded e-device compartment make it as great for commuting and travel as it is for local trails. You can adapt the same pack between a hike with belt support and a commute without the belt, while keeping a device padded.

Checkpoints once the pack is on

After loading, walk around for a few minutes and check these points. The catalog does not provide specific fit measurements, so use your own comfort as the guide.

  • Belt contact: The waist belt should sit on your hips and stay in place without digging in. If it rides up, tighten it slightly; if it restricts breathing, loosen it.
  • Shoulder strap tension: The shoulder straps should curve over your shoulders without gaps. You should be able to slide a finger under them, but they should not feel loose.
  • Load stability: Bend forward and side to side. The pack should move with your back, not swing away. If it shifts, tighten the rolltop or reposition heavier items closer to your back.
  • Device compartment: If you carry a tablet or laptop, confirm it sits flat and does not press into your back. The padded compartment is designed to protect a device, but the catalog does not specify a maximum device size.

What the supplied information does not cover

The catalog does not list a liter capacity, torso length range, strap dimensions, or specific care instructions for the ALL-IN PACK 30. It also does not describe how to adjust the rolltop beyond closing it. For those details, check the product label or contact the retailer. Use the fit steps above as a starting point, and adjust based on how the pack feels on your own body.

Related Articles

Customer Service
Home
Products
Cart
Profile